Two C6 Corvettes, turned away everywhere else
Two C6 Corvettes came through the Fraser shop in the same week with the same story: both had been turned away by multiple tint shops, and both for the same reason, that notorious C6 rear window. We tinted both of them first try, start to finish in about an hour each, rear glass included.
No seams, no relief cuts, no "we'll have to piece it." Just two clean installs on a car most shops won't take on.

Why the C6 rear window scares off most shops
The C6's rear glass is the problem child of automotive tint. It's a large piece of deeply curved, compound glass, meaning it bends in two directions at once. Lay a flat sheet of film against it and the film immediately tents and throws fingers, those creases that bunch up where flat material meets a curve it can't follow.
That's where the shortcuts come in. Some shops refuse the car outright. Others cut the film into pieces to force it down, leaving visible seams across the back glass. The right way is to shrink a single piece to the curve with heat before it ever goes on, and that takes the right film, the right technique, and the patience to do it in stages.
Our tint process on these C6s, step by step
Same process on both cars, and the whole thing lives or dies on one step. Here's how each C6 went from turned-away to tinted.
Inspection and film choice
Each car got the same once-over: glass checked for chips and old film, defroster lines noted, and the rear hatch sized up for what it would take. On a C6, the film matters as much as the hands, so we reached for a ceramic film with the shrink characteristics to lay down on a deep compound curve without fighting back. Shade and VLT were set to what each owner wanted, kept inside Michigan's legal limits up front.
Deep clean and glass decontamination
Every window cleaned inside and out, then razor-scraped to lift baked-on residue and road film the eye doesn't catch. The rear glass especially gets a surgical clean, because once a piece this size is formed and laid, a single trapped speck means pulling it and starting over.
Heat-forming the C6 rear glass
This is the step that turns shops away. We laid the film on the outside of that big curved hatch and worked it with a heat gun and hard card, shrinking the fingers down in stages until a single sheet sat tight to the compound curve with no tenting and no seams. It's slow, deliberate work, and it's where experience shows: rushed or under-heated, the rear glass creases or lifts within weeks; formed properly, it simply disappears into the glass.
Interior application and edge tucking
With the rear pattern formed, each pane went on inside with slip solution and was squeegeed from the center out, the one-piece rear glass set carefully into place and the door and quarter glass tucked at the edges. Every bubble and trace of moisture was driven out of one piece before moving to the next.
Final inspection, cure, and care
We inspected every window edge to edge under light, the rear glass most of all, then walked each owner through the cure: keep the windows up for a few days, expect a little haze or a few water pockets that clear as the adhesive sets, and skip ammonia cleaners. In cooler Michigan weather full curing can run a few weeks, and the film is backed by a lifetime warranty.
How both turned out
Both C6s went out the same day they came in, first try, about an hour each, rear glass and all. Clean single-piece back glass with no seams and no fingers, even glass all around, and fronts kept inside Michigan's legal limits, all backed by a lifetime warranty on the film.

One of the owners left a five-star review afterward:
"One of the few places willing to do C6 Corvette hatch glass, and they did it 10 out of 10. Highly recommend these guys!"
Told your car is "too difficult" to tint?
A tricky rear window is a reason some shops pass. For us it's the kind of job we'd rather take on. If you've been turned away because of your back glass, a C6 Corvette or anything else with a hard curve, bring it our way.
Drivers make the short trip from Roseville, Warren, Sterling Heights, and Clinton Township for exactly this kind of work. Come by the Fraser shop and we'll take a look at yours.
